Context Plus CFP Standard 8 Zone Conventional Fire Alarm Panel (CFP708-4)

Name: Context Plus CFP Standard 8 Zone Conventional Fire Alarm Panel (CFP708-4) - pusatfiresafety.com
Rating: 4.00 (1 reviews)

Brand	Context Plus
Type	CFP708-4
Function	Panel Controller

Context Plus CFP Standard 8 Zone Conventional Fire Alarm Panel, LPCB Certified To EN54-2_4 (CFP708-4)

In Stock

Conventional Fire Alarm Panel CFP708-4 adalah panel control fire alarm sistem deteksi kebakaran convensional 8 zone yang telah tersertifikasi LPCB sesuai standar EN54-2/4.

Order on WhatsApp

Add to Wishlist

Category: Panel Controller Tags: 8 Zone, CFP708-4, Context Plus, Conventional Fire Alarm Control Panel, MCFA, Panel Controller

Always In Stock, Always Ready to Serve

Free Shipping applies to all orders over $500 for DKI Jakarta only
Guranteed 100% Originals
Guarantee all products at the lowest price

Conventional Fire Alarm Panel CFP708-4 adalah panel control fire alarm sistem deteksi kebakaran convensional 2 zone yang telah tersertifikasi LPCB sesuai standar EN54-2/4.

Panel ini menawarkan:

8 zone detektor dengan 4 sirkuit sounder convensional
Desain casing plastik modern (flush/surface mounted)
Dilengkapi input perubahan kelas dan peringatan
Relay kebakaran dan gangguan terintegrasi
Sistem keamanan kombinasi keypad/kunci
Fitur teknis meliputi delay zone yang dapat diatur, fasilitas coincidence & non-latching zone
Dilengkapi sistem pengujian dan pencarian gangguan
Tersedia opsional repeater dan papan ekspansi relay
Harga kompetitif dengan fitur lengkap untuk pengguna dan installer

Cocok untuk instalasi sistem alarm kebakaran skala kecil-menengah yang membutuhkan sistem yang andal dan mudah dioperasikan.

Power Supply Specification
Mains supply voltage	230V 50/60Hz
Mains rated current	350mA maximum
Internal power supply	19V – 28.5V (27V nominal). Ripple 7V maximum (battery fault)
Total output current limited to	1.5A @ 230Vac (ImaxA = 146mA)
Supply and battery charger monitored for failure	YES (battery charger is also temperature compensated)
Batteries monitored for disconnection and failure	YES
Batteries protected against deep discharge	YES (Deep discharge cut off approx. 21 volts)
Max. battery size and type	2 x 12V 3.2Ah VRLA connected in series (use YUASA NP3.2-12 for LPCB approved systems) Minimum battery size = 1.2Ah
Mains fuse	240V 1A HRC ceramic 20mm compliant with IEC (EN60127 PT2)
Battery fuse	1.6A F 20mm compliant with IEC (EN60127 PT2)
Current draw from battery (Mains failed)	1.5A maximum

Detector Circuit Specification
Number of circuits/zones	2 (CFP702-4), 4 (CFP704-4) or 8 (CFP704-8)
Max cable length per circuit	500 metres
Cable type	Fire resistant screened cable, minimum conductor size 1mm2
Connector blocks	Plug-on type, largest acceptable conductor size 1.5mm2
Line monitored for open circuit and short circuit	YES – DC monitoring
Line monitored for detector removal	YES – end of line monitoring device modules provided
Max. allowable impedance (each conductor)	20 Ohm
Max. cable capacitance	0.27uF
Call point resistor value	470 to 680 Ohm
Max. number of smoke/heat detectors per zone	25
Max. combined number of detectors & call points	32 per zone

Sounder Circuit Specification
Number of circuits	4
Max cable length per circuit	500 metres
Cable type	Fire resistant screened cable, minimum conductor size 1mm2
Connector blocks	Plug-on type, largest acceptable conductor size 1.5mm2
End of line resistor value	6800 ohm 5% Tol. 0.25W (blue, grey, red, gold)
Each circuit monitored for open and short circuit	YES – reverse voltage DC monitoring. Indicated by common fault
Alarm voltage	27V maximum, 20V minimum (final battery voltage)
Sounder circuit fuses (one per circuit)	Resettable type (200mA min. hold current; 400mA max. trip current; 50mA when tripped. Reset when faults removed)
Max. total sounder output current to all outputs	4 x 200mA = 800mA
Max. No. of bells @ 25mA	32
Max. No. of electronic sounders @ 20mA	40 (sounders must be polarised)

Auxiliary Relay Outputs
Aux. Fire relay output (AUX)	Voltage-free single pole changeover; Max switching current 1A; Max. switching voltage 30Vdc voltage 30Vdc
Fault relay output (FAULT)	Voltage-free single pole changeover; Max switching current 1A; Max. switching

Auxiliary Open Collector Outputs
Reset output (RESET)	Non-monitored open collector type; Active during reset cycle; Max. sink current 30mA; Max. open circuit voltage 27Vdc
Remote output (REM)	Non-monitored open collector type; Active during any unsilenced fire condition (provided all relevant delays have expired); Max. sink current 30mA; Max. open circuit voltage 27Vdc
24V aux power output (for use with the above)	Output protected by a resettable fuse (100mA min. hold current). Resets when fault removed

Auxiliary Inputs
Class Change (makes sounders sound continuously)	Connect to OV to trigger. Max. input voltage 27V (non-latching)
Alert (makes sounders pulse intermittently)	Connect to OV to trigger. Max. input voltage 27V (non-latching)

User & Engineer Controls
General user controls (access level one)	User & Engineer Controls
Authorised user controls (access level two)	“Silence alarm sounders; Activate alarm sounders; Reset the system; Test the lamps; (Entry via keypad code or keyswitch); Disable/enable zones; Disable/enable fault output; Disable/enable remote output; Disable/enable sounders; Disable/enable auxiliary output; Disable/enable output delays”
Engineer controls (access level three)	Program coincidence (double knock); Invoke one man walk test; Program delays; Set up zones for non-latching operation; Program sounders to resound (or not resound) when a new zone enters alarm; Enter fault diagnostic facilities

Indicators
External indicators	General fire; Zone fire; Zone fault; Zone disabled; Zone test; Supply present; Remote output activated; Remote output status; Test; Accessed; General disablement; Fault output status; General fault; System fault; Repeater fault; System status; Sounder status; Power supply fault; Auxiliary output status; Output delays
Internal indicators	System fault (distinguishes between watchdog, site memory and phase lock loop faults); Zone fault (distinguishes between open circuit and short circuit faults); Hazardous voltages present; Repeater fault (indicates which repeaters, if fitted, are faulty)

Dimensions
Physical size	Size = 380 x 235 x 96mm approx.
Weight	1.75kg (without batteries)

Operating conditions
The components are selected to operate within their specification when the environmental conditions outside the enclosure comply with class 3k3 of IEC 721-3-3:1978. Temperature range: -5 to + 40°C. Maximum relative humidity: 95%